Home
About us
Heavy Duty Saws
Medium Duty Saws
Single Strand Wire Saw
Polishers
CO.ME.S. Polishing Heads
Cut Off Saws
Specialty Equipment
S&K Splitters
Marchetti CNC Equipment
Conveyors
Turntables
Water Filtration Systems
Helios System Natural Stone Process
Used Equipment
Customer Pages
Contact


Single Head Polishers


  • 2- 10" Square Tubes for the Main Beam Assembly
  • Mitsubishi PLC and a Maple's Keypad on the Control System for setting up Slabs
  • A/C Variable Speed Drive on the Cross Travel
  • Direct Wheel Drive on the Gantry
  • 20 HP- 3 Phase Main Motor
  • 40 FT of 2" CF Rails and 6 Pitch Gear Rack for the Runway
  • Hardened Rods and Ball Sleeve Bearings on the R & L Assembly
  • Joystick for Manual Operations and Setup
  • 1- CO.ME.S 5 Brick OR 1- CO.ME.S 6 Brick Polishing Head



  • 2- 10" Square Tubes for the Main Beam Assembly
  • Mitsubishi PLC and a Maple's Keypad on the Control System for setting up the Multiple Head Operation
  • A/C Variable Speed Drive on the Cross Travel and Gantry Main Motor
  • Direct Wheel Drive on the Gantry Movement
  • Programmable Up and Down Pressure for the Polishing Heads
  • Cam Follower Bearings on the Cross Travel for the Saddle Motion
  • 2" Hardened Rods w/ Nylon Guide Linear Bearings for the R & L Travel
  • Omni Directional Joystick for Manual Positioning
  • 20 HP- 3 Phase Main Motor
  • 40 FT of 2" CF Rails and 6 Pitch Gear Rack for the Runway
  • Heavy Duty Gearbox for the Gantry and Cross Travel
  • 7- CO.ME.S 6 Brick Polishing Heads
  • 7- Head Adapters and a 7 Head Storage Rack




  • 2- 10" Square Tubes for the Main Beam Assembly
  • Mitsubishi PLC and Maple's Keypad on the Control System for Setting up the Multiple Head Operation
  • High Speed Counter  on the Verticle Travel
  • Hydraulic Pressure Control
  • Digital Readout for Hydraulic Pressure
  • A/C Variable Speed Drives on the Gantry Main Motor and Cross Travel
  • 2" Hardened Rods with Thompson Linear Bearings for the R & L Travel
  • 2" Thompson Linear Ways and Bearings on the Cross Travel
  • Ball Screw w/Extension, Gearbox, and Motor for the Calibrator
  • Pulley System for incresed RPM's
  • 4- Position Joystick for Manual Positioning
  • Programmable up & Down Pressure for the Polishing Heads
  • 30 HP- 3-Phase Spindle Main Motor
  • 30 HP- Inverter
  • Precision Valves
  • Calibration Mode Upgrade
  • 7 Head Storage Rack and 7 Adapter Plates
  • 1- Damp 6 CO.ME.S Head for Calibrating
  • 6- 6 Brick HT CO.ME.S Heads
  • 40 FT of 2" CF Rails and 6 Pitch Gear Rack for the Runway


8 Head Line Polisher located at Ashfield Stone in Massachusettes.


The LCP8000 machine is composed of 8 individual head units (2 calibration heads and 6 polishing heads) that are mounted to a common moving bridge assembly.  The continuous slider bed belt conveyor moves the stone under the heads and thru the machine.

The operating height for the calibrators is programmable.  The operating heights for the polishing head units are set by an automatic program before the polishing mode is activated.

Air pressure type and amount is programmable for each head.

The slider conveyor assembly has a 6 ft. wide belt that is actuated by 2 large roller drums, one at each end.  Belt speed is fully adjustable.

Capacities: 

  • Min. Stone Thickness:  1/2"
  • Max. Stone Thickness:  6"
  • Min. Stone Width:  12"
  • Max. Stone Width:  6'- 0"
  • Min. Stone Length:  3'-0"
  • Max. Stone Length:  Limited by the Length of the Conveyor.




Top